Wednesday, 18 May 2016

Return to the Speedway

So we made it! 

The car is repaired and back in one piece after crashing out in a racing incident during the opening round of the season last month.  

We like Rockingham speedway nr Corby a lot! It's a compact 2 mile race track incorporated into the oval speedway, which needs a well setup car and a brave driver to get the best out of it. 

After a couple of years based in the outer paddock we have the benefit of pit garages and are right in the centre of the action.   

Also this round marks the introduction of the Toyo R888R, replacing the R888 as the standard tyre for the championship.  

As expected pretty much all the other drivers have bought new rubber and tested to understand any difference. Comments range from little difference to transformational. For now we will stick to the original spec tyres.

A last minute gap in the timetable afforded us and early shakedown test ensuring the car felt fine after its recent re-assembly.  After a quick pit stop for tyre pressures we got a few quick laps in going 2 seconds faster than ever before. 

Qualifying
We were last to the assembly area for Qualifying so decided to sit in the pits for a minute and go out alone on the empty half of the circuit. I immediately went as fast a in practice and managed to improve a little right at the end of the session too, qualifying an impressive 5th place. 



Race 1 - Saturday PM
I got a poor start and dropped 5 places off the grid, but managed to salvage one or two round the first corner.  It took a few laps too long to size up and pick off the next couple of cars.  Being right on someone tail is sometimes harder as you normalise to their braking and acceleration points.  With a DNF from front runners I finished a fantastic 5th place.  

Race 2 - Saturday PM
The final race of the day came round fast, with little time to clean brakes and tyres and consider adjustments.  I went very slightly stiffer on suspension and kept everything else the same. 

We were kept waiting the assembly area for what feel like ages, as a Fiesta Junior was recovered from an impact with the unforgiving concrete pit wall. 

A better start this time, but still lost a couple of places. I again closed quickly on the cars in front. One went wide under pressure allowing me to skip past, the other required a more forceful pass. I was able match the cars ahead for pace, but wasn't able to close the gap. As the race concluded I seemed to catch slower cars to be lapped in all the wrong places. (Round the outside of turn one banking on the marbles was tricky to say the least) holding on for another 5th place.  

Race 3 - Sunday AM 
The the traditional reverse grid and and I struggled with over heating tyres, never quite feeling as confident as the day before.  I followed a road-train of cars battling for lower positions until the inevitable spin occurred.  With the mantra. Of "No Damage" I was overly cautious in avoiding them and found myself dead last of the Boxsters.  We finished a credible 8th with passes, spinners and DNF's. 


A great result over the weekend, not only one without any damage, but where we finished as high as realistically possible and showed it does not take take two sets of new tyres and days of testing to be competitive,.



Wednesday, 6 April 2016

An early bath at Snetterton

The 2016 season opener at Snetterton circuit in Norfolk started well as I put my learning from our shakedown test Into practice posting the 5th fastest time in qualifying, nearly 1.5s improvement over our shakedown trackday time. 


This year we've switched to an SJCAM 4000 camera which is fixed using go-pro compatible mounts on the rollcage.  It has much better video & sound than our previous camera, and also still has a "car" mode which automatically starts recording once the ignition is on via a 12v to usb power lead. No forgetting to turn it on, or flat batteries!  


You can see from my lap timer (behind the gear stick) how the lap timer unfolds vs. my best previous lap. 

The display is a Chinese Android 5" smartphone running the Racechrono app.

The top left of the screen is the best lap so far, and the bottom right the split time which is constantly updated. Green is faster, Red slower.  You can see I'm checking on the straights so know to take the final corner steady (no mistakes) and bank the new fastest lap over the finish line.


The sun was out and it was a glorious spring day. Learning a lesson from last year, we made no changes to setup, simply refuelled and went out for race 1 later in the afternoon.   Tyre pressures were reduced though as they got a bit too hot (32psi) during qualifying. 








On the grid the car in front stalled immediately the lights went out and I had to take swift action to dart around the stranded car.  Avoiding it and the pit wall was a feat in itself.  Going into the first corner I was a couple of places down as a result l, but confident of getting them back. 




As the pace picked up I closed on the 5th place car but overcooked it into the long right hand final turn.  Whilst I sorted out the oversteer  two cars sneaked past on the inside - More work to do now I thought to myself! 

Over the next few laps I passed the first car several times, but never quite got into the right position to take the (faster in a straight line 987 model) in front.  Everytime I got close, I stopped defending and allowed the car behind back passed.  This cycle repeated for a while.  

Going into the the fast (70mph) left Hamilton corner the car in front suddenly lost the back end and slewed sideways across the track.  I've had this before - but I was so close behind this time. Jumping on my brakes bought some thinking time to decide to go left or right around the spinner.   As I went right into the grass the car spun backwards into my front left corner. 



I immediately knew it was race over, with water pouring the the front radiator.  Sadly for everyone the other car was standard on the edge of the circuit causing the red flags to come out. 

On getting back to the pits it became obvious our weekend was over too.   Damage was extensive to the front left wing, bumper, radiator, suspension and steering.   Offers of help were received but it would be a long job and we simply could not afford to replace all the parts at the track.  



For the first time ever we manhandled the car onto our trailer and returned home for an early bath. 

** Update - A day later, the car is already stripped and we have a few weeks to source cheap second hand or OEM parts to repair it for the next round at Rockingham in mid May. 


Friday, 25 March 2016

Final Shakedown Test

In seven days time well be taking part in the first BRSCC Porsche Championship meeting of the year, being held at the Snetterton circuit in Norfolk.  

We haven't raced there for three years, so booked a standard MSV track day to shakedown the car, get my eye in on the circuit and let some family have a go at the same time. 

The MSV instructors read the riot act in the briefing, as recent events had been treated like test days (overtaking anywhere) and not track days, where novices and experienced drivers need to co-exist.  

It worked as track etiquette was good and the mix of classics, road cars, sports and race cars got on fine.  The weather was bright, dry and about 10 degrees.  Hopefully it will be the same come race day.  

In the morning we did a few runs focused on checking the reliability of the car.  The only issue we found was a loose engine cover, so all went well.  Handling was good with our guess at the setup.  No particular oversteer or understeer issues - but the front end was bouncing up and down a bit too much on corner exits.  


The trick with open pit lane format days is to be on track when everyone else isn't.  A couple of times we noticed the track was full, with cars queueing in the pit lane.  This meant that in about 15 mins it would be empty as they all come in to cool down - time for us to head out then!

In the afternoon we experimented with setup, corner techniques and gear choices.  The track was far less busy too. 

  • Snetterton is flat and fast, so the setup is likely to be fairly stiff on roll bar and damper setup. We went a bit too hard initially, finding the front end skidding under braking, especially into the hairpin corners. In the end we think we found a good compromise.  


  • The Boxster gearbox is highly geared to reach 160mph.  There are always corners     around the 50mph mark which can either be taken in 2nd (screaming near the rev limit) or 3rd (lower revs and not enough torque).  On the long straights we also have the option of short shifting to 5th gear or holding onto 4th to the rev limit as we approach 130mph.

  • Also for the tighter turns we have the option of following the theoretical racing line of a late turn in, apex 3/4 round the turn and a straighter exit.  Or experimenting with bringing the car in earlier, tighter and slower, but covering a shorter distance round the corner.  Each corner is unique and it often depends on the length of the following straight as to which yields a faster lap time.  
Overall it was a really successful day, without incident, and I went faster than ever.





Monday, 14 March 2016

Winter Overhaul

We've spent roughly a day per month over the off season sorting the car out.  Here's the run down on most of it.  

First up was to repair the damage from the last round of 2015 at Silverstone.  This required a new front wing and door to be sourced.  Luckily I got used panels in really good condition and in the right colour so we just had to unbolt and swap them over.



The remainder of the damage had to be done by a processional body shop.  I used Lemass_Automotive in Buckinghamshire who pulled the lower sill dent out, resprayed my spare front bumper and fixed and painted the door dents on the drivers side.   The rear quarters could not be straightened without a lot of painting, so were left as-is and are hardly noticeable. 
Secondly we drained the coolant and refilled with the correct mix of anti freeze.  It just got filled with water in a hurry at Silverstone so needed to be sorted to ensure the engine didn't freeze over the winter.

Next we had the oil flushed and replenished with Millers 10/50 nanotech and had to top up the power steering fluid again - as the top had come loose. (No leaks though!)

On the inside of the car we stripped all of the remaining wiring in the inner doors and replaced the big clunky door check straps with light weight fabric ones.  Its small beer, but a 2kg weight saving is still a saving.

We then partially stripped some of the excess wiring from the main loom. Starting with the relay board in the boot forwards to the front of the car.  There is a huge amount of wring still to come out, but this will have to wait until we have more time to remove the dashboard.  
We should have done this when the car was first converted - but we just didn't have the gumption and experience to go all out race car back then.

The third big job was to replace the exhaust again.  The cheap Chinese made one we ran last year had disintegrated internally.  It was rattling and overly noisy, risking us failing more noise tests. 


The replacement is fairly stock in terms of loudness and much better made from Top Gear exhausts. 












The penultimate job was to turn our attention to the braking system.  A flush through with new Castrol SRF racing fluid, bleeding any air out of the system.  We use a simple pressure bleeder which runs off the tyre pressure to saving pumping the pedal manually.  

A new set of rear brake pads were also fitted.  Once they get more than half worn (<5mm) they tend to overheat quickly and braking performance reduces.  The wear also gets progressiveness quicker, so the last 3-4mm can go in a race or two.




The last piece of weight saving has been removing the handbrake.  This entailed removing the rear discs, to release the handbrake cables and remove the now  superfluous brake shoes.  In the car the handbrake lever, mounting and cable adjuster goes too.  This is another 5kgs gone. 

The final job was to fit an additional MSA LED brake light in the centre of the rear bumper.  Whilst we have happily used the two std rear fog lights to meet the regulations, some racers have had issues with scrutineers. The series regulations now state we have to run this regardless.




Thursday, 10 March 2016

2015 Best Bits

As we get close to starting the 2016 race season, I compiled the best bits of action from our on-board camera.   Lots of very close racing, overtakes, spins (not me), and a few offs. 


Tuesday, 15 December 2015

Ice Mode Brakes


When you jump on the brakes, the pedal goes rock solid hard, you cannot add braking pressure and there is no noticeable braking effect.  

This is what the Internet community describes as "Ice Mode" and it's a pretty hair-raising experience when it occurs. 

This has happened to me a couple of times, when braking on a slippery surface on track. 

Each time caused me a visit to the gravel trap, a DNF result in each race, and most recently some damage to the car.  So I wanted to understand how to fix it or rather as I've found out... avoid and manage it.

There is a lot of talk on Internet forums; not limited to Porsche, of the infamous ice mode. Much of it is interspersed with comments from people having brake fade, over heating or other braking issues.  Ice mode is entirely different though.

The general consensus is that modern Bosch road ABS isn't designed for the extremes of the track.  In a small no. of scenarios the system can be overwhelmed or act irrationally based on the signals from its sensors.  

Ice mode seems to happen when the ABS system is running at its maximum to prevent any particular wheel from locking-up.  It is venting pressure to allow some wheel rotation, but at the same time trying to apply pressure many times per second.  This deadlock scenario results in virtually no braking effect.

The finger seems to point to the ABS controller, which is unable to meet the demands of all the sensors and inputs, some needing braking force applied others released.  These sensors include, brake switch, pedal, accelerometers, yaw sensors and wheel speed sensors.  When the system is working so hard to prevent locking of multiple wheels, it doesn't permit enough force to be applied to the remaining wheels to have any affect in slowing the car.  The ABS is simply at the limit of its design in these situations.

If the car has PSM (Porsche stability management) this adds another input and seems to increase the chance of ice mode.  

The ultimate fix is to buy a Porsche 911 Cup car which is designed for the track from the off. Bosch also do a retro fit racing ABS system. However this is out of the question for most on cost grounds, and probably race regulations for the different series.  It is also far easier to mitigate the issue.  

The main cause for me has been jumping on the brakes hard and fast when the track surface is slippery. 

My racing style was to brake very hard and very late into corners, using ABS everywhere. There seem to be other contributing factors too, such as running non-factory wheel sizes or overly sticky tyres which would increase the demand on the ABS system which can also increase the likelihood of ice mode occurring.


Once you experience ice mode - there is only one way to get out of it.  Lift of the brakes and re-apply. Good old fashioned non ABS braking techniques.  
This works - but you've probably lost at least half your braking distance - so it might not ultimately help make the corner. 


Avoidance or minimising the few situations when ice mode might occur is a better strategy. This means applying braking force quickly but more gently, before going harder onto the brakes. The ABS is still likely to come on under hard braking, when it does it makes sense to modulate the braking force, rather than keep your foot in and let it become overloaded.

This technique is more mechanically sympathetic, and it also has a less destabilising affect on the car at turn in and corner entry, allowing for higher speeds to be carried through the turns.  It should make you a smoother and faster driver, regardless.