Thursday, 11 June 2015
Rockingham Race TV
We featured heavily in the Motors TV coverage after going from 11th to 4th in Race 1 at Rockingham.
Labels:
race video,
tv
Wednesday, 20 May 2015
2015 Season Starts at Rockingham Speedway
We made the trip up to Corby to the Rockingham Speedway for our first event of the 2015 season. The outer paddock is not the most glamorous of places on the BRSCC Calendar, but we made do, setting our trailer down alongside some of the other drivers who run with race trucks and awnings. Many had tested the day before, but were remaining tight lipped about how they'd got on!
Scrutineering completed without a hitch which is always good. And at 10:30am on the Saturday we headed round to the infield section and out onto the track for 20mins of Qualifying.
I immediately realised something was not right with the engine. Erratic idling in the holding area escalated to hesitation every time I went between 5000-6000 RPM. Intermittent at first, I headed back to the pits as red flags came out for an accident. A quick chat in the pits decided there was nothing we could do, and with the track back open I headed back out. Using a higher gear round some corners and gingerly taking the banked oval track section (usually flat out at 110mph) I qualified 11th 2secs off my expected pace.
Back in the paddock we immediately found the airbox was broken causing erratic air flow past the Mass Air Flow sensor (MAF). An extra jubilee clip solved the problem and will ensure it doesn't return.
Feeling confident that the car was now running fine and with a slight suspension tweak to dial out some over-steer I went out for Race 2 on Saturday afternoon.
I climbed 3 places on the opening lap. A couple of cars spun off under pressure, falling to the back, whilst another two collided bringing out the safety car. Running in 4th place, eying up a first ever podium, I spun up the rear tyres too much as the safety car pulled off and this led to loosing a place a lap later. A three-way battle for 3rd place finished with me reclaiming 4th for my best ever finish.
Race 1 Video
A great social event and BBQ was put on that evening in the paddock before we headed off to the hotel.
On Sunday I had to add the obligatory "Championship Success Ballast" which was 20kg's for my 4th place finish. This took me to 50kg's over the minimum weight so I still need to lose some more from somewhere.
The two races didn't quite go to plan. A poor start in Race 2, left me high on the outside of the banked first corner. Another car tried to go higher in my blind spot and we collided as the pack of cars ran out to the wall of the track. I got lucky with a slight dent and an unbalanced wheel, whilst the other car sustained lot of damaged with the wall.
The two races didn't quite go to plan. A poor start in Race 2, left me high on the outside of the banked first corner. Another car tried to go higher in my blind spot and we collided as the pack of cars ran out to the wall of the track. I got lucky with a slight dent and an unbalanced wheel, whilst the other car sustained lot of damaged with the wall.
The final race started reasonably, although I lost a lot of places off the grid (reversed so I started 2nd). Then on lap 2, my brake pedal went solid and I careered off into the gravel for a rare DNF.
Race 2 Video - https://youtu.be/0sky5078Gz0
Race 3 Video - https://youtu.be/V_yHiCZctMY
A weekend of highs and lows. Another situation where we managed to resolve technical problems with the car ourselves. On the down side we absolutely need to fix the power steering pump which continues to leak, and likely also need the alternator replaced (potential cause of ABS failure).
Two outstanding additional performance modifications are also overdue; GT3 suspension arms, which will increase corner grip plus the under-drive pulley to slow the ancillaries and increase power a little.
Next race for us is Donington Park in July.
Labels:
race report
Thursday, 26 February 2015
Monday, 23 February 2015
Winter Upgrades and Servicing
Three years of racing is starting to take its toll on the Boxster with some wear and tear items needing to be addressed.
The leaking power steering fluid has been fixed by replacing the o-ring seals between the reservoir tank and the pump. Access is very tight on top of the engine so we're hoping a full replacement is the pump isn't needed.
All four brake calipers have been sent away for a full refurbishment. The diagnosis from Pro Calipers was that they have been over heating significantly. All the rubber seals were disintegrated and the paint color darkened to a deep red indicating temps of 300c+. Disintegrated seals prevents the pads retracting fully, increasing wear and heat and ultimately slowing us down.
The refurbishment included new bleed valves, seals, anti squeal shims and we also fitted the Goodridge braided hoses. The latter having sat on the "To do" list for over two years.
At the front of the car we've replaced the centre radiator which along with its bracket was on its last legs.
Whilst the front bumper was off we've added brake cooling ducts, forcing air through the front bumpers and onto the brake discs. This adds to the GT3 ducts fitted towards the end of last season as an attempt to keep brake temps down.
In the engine we re-attached the the exhaust with new clamps. The exhaust falling off was the ultimate reason for my DNF at Donington last October. It must have been knocked on the kerb going into or out of the gravel trap, but took another 10mins to properly fall off.
We needed a new inner wheel arch liner which had melted on the exhaust.
A full oil change, brake fluid flush with 2 litres of Castrol SRF and the BMC performance air filter cleaned and recharged completes the regular service items.
Friday, 12 December 2014
Running Your Own Race Car...How Hard Can It Be!
To some, the idea of running your own race car may seem daunting. There are obviously different approaches available from doing everything yourself, through to getting someone to do everything for you, plus plenty of options in-between.
We built our Race Porsche Boxster ourselves with the intent of running it ourselves. The building was part of the fun and experience. Never having done anything like this before was a challenge, took more time than anticipated, but it's the only way we can afford to compete.
If the car is reliable, well put together and you are well prepared, then running yourself over a race weekend is very achievable and also rewarding.
The work isn't complex, even for people less mechanically minded. If you can jack up a car and change a wheel or your own brake pads, it's well within the capability of a driver and an extra pair of hands to help.
In order to make a race weekend manageable, the car needs to be prepared as much as possible before each event. There is enough to do with registration, scrutineering and sorting yourself as a driver out when you arrive at the circuit.
The car needs to be ready; good enough to qualify, straight after unloading from the trailer. This typically means fueled for qualifying, battery charged, brakes cleaned, belts adjusted and roll bars/suspension setup to the baseline for the track or the outcome of any practice days. Just tyre pressures to set and go!
![]() |
| Car fully prepared and ready to qualify |
To make things easier the car setup and ambient conditions for every session on every track are logged in a spreadsheet we keep. This is for use as a reference between sessions and also for the future. This has been invaluable in saving time and giving a good baseline to work from when turning up somewhere new or when the conditions change unexpectedly.
With the car ready, it's just a case of having my race suit and boots on and gloves, balaclava and helmet in the car. Typically this is around one hour before the race time (30-40 mins before we are called to the holding area.) This is in case it rains or conditions change, leaving plenty of time to sort anything out on the car. Trying to get the car and yourself ready at the last minute just isn't possible unless you have a team of people supporting you.
Tyre pressures are set higher than needed beforehand so it's just a case of releasing air down to the desired pressure at the last minute.
I drive myself to the holding area, and tend to wait in the car, engine running/warming up. There is an order to putting balaclava, helmet, safety belts on. Then setting my lap-timer and finally putting my gloves on, since I can’t reach the dashboard once belted in. This year I have an automatic car camera which records all the time the ignition is on, which means one less thing to worry about too.
Once we come off the track, if onsite fuel is open the car can be driven there and refueled straight away to save time and effort. Otherwise jerrycans are used, but this is still typically the first job to do. You also need to give the car some time to cool down!
Before and during each race weekend the following work is typically needed:
Battery: The race battery needs to be trickle charged overnight before each event. We also make sure the engine is running when using the 12v tyre compressor as it doesn't take much to deplete the battery.
Race Harnesses: Harnesses need to be checked and adjusted before each event. To check for wear and tear and to re-adjust as needed.
Anti-roll Bars: We set these per circuit before each event, and typically don't then change them unless is rains heavily or I have time to experiment with a different setup. Takes 5 mins per side with an allen key and spanner with the wheels on.
Brakes: The drilled discs get clogged up with brake dust and need to be cleaned out after every two track sessions. Takes 10 mins per corner. We typically replace the brake discs at the same time as the pads get to 3/4 worn. Brake pads are lasting at least 3-4 events on the front, but twice that on the back.
Wheels: While the brakes are being cleaned its a good time to clean the rubber marbles off each wheel. Wheel bolts have been changed to studs and a cheap 12v impact gun helps to speed up removal and refitting. Then tighten with the torque wrench.
Suspension Stiffness: This is set before each event to a baseline for the circuit. A decision is made after each session on track as to stick or change, based on the weather or to address over or under-steer issues. Takes 1 min per corner to twist the adjuster knob and can be done with wheels on.
Battery: The race battery needs to be trickle charged overnight before each event. We also make sure the engine is running when using the 12v tyre compressor as it doesn't take much to deplete the battery.
Race Harnesses: Harnesses need to be checked and adjusted before each event. To check for wear and tear and to re-adjust as needed.
Anti-roll Bars: We set these per circuit before each event, and typically don't then change them unless is rains heavily or I have time to experiment with a different setup. Takes 5 mins per side with an allen key and spanner with the wheels on.
Brakes: The drilled discs get clogged up with brake dust and need to be cleaned out after every two track sessions. Takes 10 mins per corner. We typically replace the brake discs at the same time as the pads get to 3/4 worn. Brake pads are lasting at least 3-4 events on the front, but twice that on the back.
Wheels: While the brakes are being cleaned its a good time to clean the rubber marbles off each wheel. Wheel bolts have been changed to studs and a cheap 12v impact gun helps to speed up removal and refitting. Then tighten with the torque wrench.
Suspension Stiffness: This is set before each event to a baseline for the circuit. A decision is made after each session on track as to stick or change, based on the weather or to address over or under-steer issues. Takes 1 min per corner to twist the adjuster knob and can be done with wheels on.
I have even adjusted this in the holding area minutes before the race when it has unexpectedly poured with rain.
Tyres: Tyre pressures are critical. Too low and you have no grip until they warm up. Too high and they overheat, get greasy and loose grip into the race. Pressures change with the ambient temperature and conditions, hence our historical log is used as a guide. Usually the last thing to be set before going out onto track and takes 30 secs per wheel.
Oil/Brake Fluid/Servicing: As we only typically do 4-5 event per year this is limited to the off-season. No point in changing oil every event / 150 miles. If we did a full season then a service mid way would be sensible.
![]() |
| On axle stands during cleaning of front brake discs and wheels |
Most changes or minor problems can be tackled with a decent home mechanic tool set. The bulkiest items travel in the race car and the rest in the car boot.
- A decent low entry jack
- Axel stands
- Tyre pressure gauge
- 12v Tyre compressor
- Set of screwdrivers, socket set and ring spanners
- Set of hex/torx bits (Porsche put them everywhere)
- Brake caliper hex socket bit
- Hose clip tool
- Hand wipes, bucket and car cleaning kit
- 12v impact gun
- Torque wrench
- 2x Jerry cans plus funnel
- Cable tie, Duct tape / Electrical tape
- Spare fuses and a spare 9v fire extinguisher controller battery
- Mat to lay on and an Umbrella to keep some rain off!
![]() |
| Car boot used to store tools over the weekend. |
If you need anything else then you have a bigger problem to solve. Once or twice we have needed help from other people in the paddock to fix a problem and keep us racing. Generally people are always
willing to assist. The presence of a championship parts supplier means we don't need to carry any specific spare parts.
Of course if you end up in the gravel, having a mechanical failure or getting damaged (all of which have happened) you will need more time to sort the car out. This is when being organised and having an extra pair of hands is the difference between getting out for the next race or going home.
The methodical approach to preparation and maintenance has contributed to the fact we have only suffered two DNF's in three seasons.
The methodical approach to preparation and maintenance has contributed to the fact we have only suffered two DNF's in three seasons.
- The last lap of a race, when the gear selector broke. In hindsight I could have limped home in 4th gear!
- When the exhaust broke off, causing fumes in the cab due to being knocked over the kerb coming out of a gravel trap after going off on an oil spill.
So it's not that difficult if you are well prepared, and is extremely rewarding, especially when you out-perform those who have bigger budgets and professional support.
Wednesday, 22 October 2014
Donington Park Finals
Donington Park in the East Midlands was the final event of the season. A triple race schedule with the added twist of a reversed grid for the final race.
Having not done any changes to the car since Brands Hatch, we arrived early Saturday and set about changing the car setup (roll-bar stiffness and damper settings) to suit the fast and flowing Donington track. We also swapped our worn wheels/tyres for the spare ones which we bedded in at Brands.
Qualifying wasn't until 12pm, so the track had dried from the early morning rain by the time we went out. I needed a few laps to re-aquaint myself with the circuit and then stopped in the pits to check tyre pressures. It was warm, and they were already getting too hot, so a few PSI was let out of each corner.
I'd already gone faster than ever previously and my lap timer twice showed another half second improvement in the session, but a mistake and a slower car late in the lap meant I qualified 9th. Back in the paddock, I decided the car was still over-steering a little too much, so before the race we sorted this by adjusting the ride height before the first race.
Race 1
Paranoid about my recent bad starts, I was really cautious getting away. I lost a couple of places and was overtaken by a production spec Boxster. Handily I blasted straight back past on the next corner, and set out following the main pack of cars. A mid race safety car for two 924's in the gravel setup a 10min blast to the finish. Two cars I was battling with skidded off under pressure. I avoided t-boning one by centimeters! I finished 9th, not an amazing place, but the car was handling really well and I was confident overtaking cars for position.
Race 2
I maintained position from the start, and whilst not quite able to keep up with the front 6 or 7 cars, they were only a few seconds ahead and not getting away. Mid way through the race I came across two 924's rejoining in the middle of the track after a spin. I had to take avoiding action at over 90mph to prevent hitting them.
Breathing a sigh of relief, I descended Craner curves to a Boxster rejoining from the grass, and then my car went sideways. I only just managed to control it and didn't loose a place either. Only then did I see the trail of fluid which had been the cause of all the issues, coming from the rear of a Boxster ahead.
I now found myself in 6th place, but in the remaining laps I noticed my lap times slowing and a gaggle of cars behind definitely closing in. The last lap board finally came out but I lost a position into Redgate. Determined to get it back, I stayed wide and slingshot back past into the Old Hairpin, where I knew I could out brake.
However up the hill I stayed too far on the inside which ultimately compromised my exit speed onto the next straight and I lost the position on the penultimate corner to finish 7th. My best race result since the start of the year at Silverstone.
After the race I found the demanding braking had worn the front brake pads to almost nothing. A quick chat with the series parts suppliers Jasmine Porcha-link and I was ready for race 3 which some improved braking.
Race 3
Reverse grid is always fun. The aim is to stay at the front for as long as possible before the leaders ultimately overtake you. Starting on the 3rd row would give the that opportunity.
I worked hard on the green flag warmup lap to get my tyres warm and bed the new front brake pads in. A few might stops from 100mph plus does the trick.
I had a minor panic on the grid as the car had popped out of first gear. The rule is to get into first on the approach to your grid slot and leave it alone! But your mind plays tricks and you can't help messing with the gear stick whilst stationary.
I got away well enough though, but was boxed in behind the slower cars in front as I approached Redgate corner. At the last second a gap to the inside appeared and I darted though and into 3rd place.
I could see I was faster than the 2nd place car and keeping ahead of the faster runners behind me. On lap two I lined up a block pass into the Coppice corner to take 2nd, but this compromised my speed down the straight and a car got on the inside.
I could see I was faster than the 2nd place car and keeping ahead of the faster runners behind me. On lap two I lined up a block pass into the Coppice corner to take 2nd, but this compromised my speed down the straight and a car got on the inside.
As we approached the braking zone I braked late as usual....the pedal went solid and I careered on towards the gravel! I managed to slew the car sideways across the gravel and out the other side in a big arc to get back onto the track. Another car was left in the gravel as I rejoined and I had no idea what had happened.
It wasn't until the lap after that I saw oil flags and thick streak of oil exactly where I braked. The vibration of gravel stuck on the wheels made it impossible drive at normal pace, but I continued for a while, dropping from 6th to 10th. With 5 minutes of the race remaining, I noticed something else was wrong, the engine was now running rough and down on power. Then I had smoke coming into the cab, so hastily parked it on the unused Melbourne loop.
Despite only our second ever DNF out of 30+ races, I had a fantastic weekend on a track where I really found confidence to push the car and my driving. The car I left in the gravel finished 5th in the end which meant had I stayed on track I should have got a best ever result.
The highlights of the weekend being lots of overtakes and a few hairy moments, which cement Donington Park as my favourite track.
Labels:
race report
Subscribe to:
Posts (Atom)










