Best Action from 201's in car video
Thursday, 26 February 2015
Monday, 23 February 2015
Winter Upgrades and Servicing
Three years of racing is starting to take its toll on the Boxster with some wear and tear items needing to be addressed.
The leaking power steering fluid has been fixed by replacing the o-ring seals between the reservoir tank and the pump. Access is very tight on top of the engine so we're hoping a full replacement is the pump isn't needed.
All four brake calipers have been sent away for a full refurbishment. The diagnosis from Pro Calipers was that they have been over heating significantly. All the rubber seals were disintegrated and the paint color darkened to a deep red indicating temps of 300c+. Disintegrated seals prevents the pads retracting fully, increasing wear and heat and ultimately slowing us down.
The refurbishment included new bleed valves, seals, anti squeal shims and we also fitted the Goodridge braided hoses. The latter having sat on the "To do" list for over two years.
At the front of the car we've replaced the centre radiator which along with its bracket was on its last legs.
Whilst the front bumper was off we've added brake cooling ducts, forcing air through the front bumpers and onto the brake discs. This adds to the GT3 ducts fitted towards the end of last season as an attempt to keep brake temps down.
In the engine we re-attached the the exhaust with new clamps. The exhaust falling off was the ultimate reason for my DNF at Donington last October. It must have been knocked on the kerb going into or out of the gravel trap, but took another 10mins to properly fall off.
We needed a new inner wheel arch liner which had melted on the exhaust.
A full oil change, brake fluid flush with 2 litres of Castrol SRF and the BMC performance air filter cleaned and recharged completes the regular service items.
Friday, 12 December 2014
Running Your Own Race Car...How Hard Can It Be!
To some, the idea of running your own race car may seem daunting. There are obviously different approaches available from doing everything yourself, through to getting someone to do everything for you, plus plenty of options in-between.
We built our Race Porsche Boxster ourselves with the intent of running it ourselves. The building was part of the fun and experience. Never having done anything like this before was a challenge, took more time than anticipated, but it's the only way we can afford to compete.
If the car is reliable, well put together and you are well prepared, then running yourself over a race weekend is very achievable and also rewarding.
The work isn't complex, even for people less mechanically minded. If you can jack up a car and change a wheel or your own brake pads, it's well within the capability of a driver and an extra pair of hands to help.
In order to make a race weekend manageable, the car needs to be prepared as much as possible before each event. There is enough to do with registration, scrutineering and sorting yourself as a driver out when you arrive at the circuit.
The car needs to be ready; good enough to qualify, straight after unloading from the trailer. This typically means fueled for qualifying, battery charged, brakes cleaned, belts adjusted and roll bars/suspension setup to the baseline for the track or the outcome of any practice days. Just tyre pressures to set and go!
![]() |
| Car fully prepared and ready to qualify |
To make things easier the car setup and ambient conditions for every session on every track are logged in a spreadsheet we keep. This is for use as a reference between sessions and also for the future. This has been invaluable in saving time and giving a good baseline to work from when turning up somewhere new or when the conditions change unexpectedly.
With the car ready, it's just a case of having my race suit and boots on and gloves, balaclava and helmet in the car. Typically this is around one hour before the race time (30-40 mins before we are called to the holding area.) This is in case it rains or conditions change, leaving plenty of time to sort anything out on the car. Trying to get the car and yourself ready at the last minute just isn't possible unless you have a team of people supporting you.
Tyre pressures are set higher than needed beforehand so it's just a case of releasing air down to the desired pressure at the last minute.
I drive myself to the holding area, and tend to wait in the car, engine running/warming up. There is an order to putting balaclava, helmet, safety belts on. Then setting my lap-timer and finally putting my gloves on, since I can’t reach the dashboard once belted in. This year I have an automatic car camera which records all the time the ignition is on, which means one less thing to worry about too.
Once we come off the track, if onsite fuel is open the car can be driven there and refueled straight away to save time and effort. Otherwise jerrycans are used, but this is still typically the first job to do. You also need to give the car some time to cool down!
Before and during each race weekend the following work is typically needed:
Battery: The race battery needs to be trickle charged overnight before each event. We also make sure the engine is running when using the 12v tyre compressor as it doesn't take much to deplete the battery.
Race Harnesses: Harnesses need to be checked and adjusted before each event. To check for wear and tear and to re-adjust as needed.
Anti-roll Bars: We set these per circuit before each event, and typically don't then change them unless is rains heavily or I have time to experiment with a different setup. Takes 5 mins per side with an allen key and spanner with the wheels on.
Brakes: The drilled discs get clogged up with brake dust and need to be cleaned out after every two track sessions. Takes 10 mins per corner. We typically replace the brake discs at the same time as the pads get to 3/4 worn. Brake pads are lasting at least 3-4 events on the front, but twice that on the back.
Wheels: While the brakes are being cleaned its a good time to clean the rubber marbles off each wheel. Wheel bolts have been changed to studs and a cheap 12v impact gun helps to speed up removal and refitting. Then tighten with the torque wrench.
Suspension Stiffness: This is set before each event to a baseline for the circuit. A decision is made after each session on track as to stick or change, based on the weather or to address over or under-steer issues. Takes 1 min per corner to twist the adjuster knob and can be done with wheels on.
Battery: The race battery needs to be trickle charged overnight before each event. We also make sure the engine is running when using the 12v tyre compressor as it doesn't take much to deplete the battery.
Race Harnesses: Harnesses need to be checked and adjusted before each event. To check for wear and tear and to re-adjust as needed.
Anti-roll Bars: We set these per circuit before each event, and typically don't then change them unless is rains heavily or I have time to experiment with a different setup. Takes 5 mins per side with an allen key and spanner with the wheels on.
Brakes: The drilled discs get clogged up with brake dust and need to be cleaned out after every two track sessions. Takes 10 mins per corner. We typically replace the brake discs at the same time as the pads get to 3/4 worn. Brake pads are lasting at least 3-4 events on the front, but twice that on the back.
Wheels: While the brakes are being cleaned its a good time to clean the rubber marbles off each wheel. Wheel bolts have been changed to studs and a cheap 12v impact gun helps to speed up removal and refitting. Then tighten with the torque wrench.
Suspension Stiffness: This is set before each event to a baseline for the circuit. A decision is made after each session on track as to stick or change, based on the weather or to address over or under-steer issues. Takes 1 min per corner to twist the adjuster knob and can be done with wheels on.
I have even adjusted this in the holding area minutes before the race when it has unexpectedly poured with rain.
Tyres: Tyre pressures are critical. Too low and you have no grip until they warm up. Too high and they overheat, get greasy and loose grip into the race. Pressures change with the ambient temperature and conditions, hence our historical log is used as a guide. Usually the last thing to be set before going out onto track and takes 30 secs per wheel.
Oil/Brake Fluid/Servicing: As we only typically do 4-5 event per year this is limited to the off-season. No point in changing oil every event / 150 miles. If we did a full season then a service mid way would be sensible.
![]() |
| On axle stands during cleaning of front brake discs and wheels |
Most changes or minor problems can be tackled with a decent home mechanic tool set. The bulkiest items travel in the race car and the rest in the car boot.
- A decent low entry jack
- Axel stands
- Tyre pressure gauge
- 12v Tyre compressor
- Set of screwdrivers, socket set and ring spanners
- Set of hex/torx bits (Porsche put them everywhere)
- Brake caliper hex socket bit
- Hose clip tool
- Hand wipes, bucket and car cleaning kit
- 12v impact gun
- Torque wrench
- 2x Jerry cans plus funnel
- Cable tie, Duct tape / Electrical tape
- Spare fuses and a spare 9v fire extinguisher controller battery
- Mat to lay on and an Umbrella to keep some rain off!
![]() |
| Car boot used to store tools over the weekend. |
If you need anything else then you have a bigger problem to solve. Once or twice we have needed help from other people in the paddock to fix a problem and keep us racing. Generally people are always
willing to assist. The presence of a championship parts supplier means we don't need to carry any specific spare parts.
Of course if you end up in the gravel, having a mechanical failure or getting damaged (all of which have happened) you will need more time to sort the car out. This is when being organised and having an extra pair of hands is the difference between getting out for the next race or going home.
The methodical approach to preparation and maintenance has contributed to the fact we have only suffered two DNF's in three seasons.
The methodical approach to preparation and maintenance has contributed to the fact we have only suffered two DNF's in three seasons.
- The last lap of a race, when the gear selector broke. In hindsight I could have limped home in 4th gear!
- When the exhaust broke off, causing fumes in the cab due to being knocked over the kerb coming out of a gravel trap after going off on an oil spill.
So it's not that difficult if you are well prepared, and is extremely rewarding, especially when you out-perform those who have bigger budgets and professional support.
Wednesday, 22 October 2014
Donington Park Finals
Donington Park in the East Midlands was the final event of the season. A triple race schedule with the added twist of a reversed grid for the final race.
Having not done any changes to the car since Brands Hatch, we arrived early Saturday and set about changing the car setup (roll-bar stiffness and damper settings) to suit the fast and flowing Donington track. We also swapped our worn wheels/tyres for the spare ones which we bedded in at Brands.
Qualifying wasn't until 12pm, so the track had dried from the early morning rain by the time we went out. I needed a few laps to re-aquaint myself with the circuit and then stopped in the pits to check tyre pressures. It was warm, and they were already getting too hot, so a few PSI was let out of each corner.
I'd already gone faster than ever previously and my lap timer twice showed another half second improvement in the session, but a mistake and a slower car late in the lap meant I qualified 9th. Back in the paddock, I decided the car was still over-steering a little too much, so before the race we sorted this by adjusting the ride height before the first race.
Race 1
Paranoid about my recent bad starts, I was really cautious getting away. I lost a couple of places and was overtaken by a production spec Boxster. Handily I blasted straight back past on the next corner, and set out following the main pack of cars. A mid race safety car for two 924's in the gravel setup a 10min blast to the finish. Two cars I was battling with skidded off under pressure. I avoided t-boning one by centimeters! I finished 9th, not an amazing place, but the car was handling really well and I was confident overtaking cars for position.
Race 2
I maintained position from the start, and whilst not quite able to keep up with the front 6 or 7 cars, they were only a few seconds ahead and not getting away. Mid way through the race I came across two 924's rejoining in the middle of the track after a spin. I had to take avoiding action at over 90mph to prevent hitting them.
Breathing a sigh of relief, I descended Craner curves to a Boxster rejoining from the grass, and then my car went sideways. I only just managed to control it and didn't loose a place either. Only then did I see the trail of fluid which had been the cause of all the issues, coming from the rear of a Boxster ahead.
I now found myself in 6th place, but in the remaining laps I noticed my lap times slowing and a gaggle of cars behind definitely closing in. The last lap board finally came out but I lost a position into Redgate. Determined to get it back, I stayed wide and slingshot back past into the Old Hairpin, where I knew I could out brake.
However up the hill I stayed too far on the inside which ultimately compromised my exit speed onto the next straight and I lost the position on the penultimate corner to finish 7th. My best race result since the start of the year at Silverstone.
After the race I found the demanding braking had worn the front brake pads to almost nothing. A quick chat with the series parts suppliers Jasmine Porcha-link and I was ready for race 3 which some improved braking.
Race 3
Reverse grid is always fun. The aim is to stay at the front for as long as possible before the leaders ultimately overtake you. Starting on the 3rd row would give the that opportunity.
I worked hard on the green flag warmup lap to get my tyres warm and bed the new front brake pads in. A few might stops from 100mph plus does the trick.
I had a minor panic on the grid as the car had popped out of first gear. The rule is to get into first on the approach to your grid slot and leave it alone! But your mind plays tricks and you can't help messing with the gear stick whilst stationary.
I got away well enough though, but was boxed in behind the slower cars in front as I approached Redgate corner. At the last second a gap to the inside appeared and I darted though and into 3rd place.
I could see I was faster than the 2nd place car and keeping ahead of the faster runners behind me. On lap two I lined up a block pass into the Coppice corner to take 2nd, but this compromised my speed down the straight and a car got on the inside.
I could see I was faster than the 2nd place car and keeping ahead of the faster runners behind me. On lap two I lined up a block pass into the Coppice corner to take 2nd, but this compromised my speed down the straight and a car got on the inside.
As we approached the braking zone I braked late as usual....the pedal went solid and I careered on towards the gravel! I managed to slew the car sideways across the gravel and out the other side in a big arc to get back onto the track. Another car was left in the gravel as I rejoined and I had no idea what had happened.
It wasn't until the lap after that I saw oil flags and thick streak of oil exactly where I braked. The vibration of gravel stuck on the wheels made it impossible drive at normal pace, but I continued for a while, dropping from 6th to 10th. With 5 minutes of the race remaining, I noticed something else was wrong, the engine was now running rough and down on power. Then I had smoke coming into the cab, so hastily parked it on the unused Melbourne loop.
Despite only our second ever DNF out of 30+ races, I had a fantastic weekend on a track where I really found confidence to push the car and my driving. The car I left in the gravel finished 5th in the end which meant had I stayed on track I should have got a best ever result.
The highlights of the weekend being lots of overtakes and a few hairy moments, which cement Donington Park as my favourite track.
Labels:
race report
Saturday, 27 September 2014
Brands Hatch Festival of Porsche
Whilst the event was primarily a Porsche Club GB event for their members, it was well advertised and open to the public. We were invited to race as part of the on-track action in addition to a lot of static Porsche displays.
We arrived on Saturday and did some testing as I hadn't driven the car for several months. We also changed the setup to suit the slower corners of the Brands Indy circuit. A more over-steer prone approach was tried to help the acute under-steer out of the last corner. This comes with a greater risk of spinning and took a reasonable amount of time to get used, and is a not the normal way I set the car up.
Sunday AM Qualifying:
As the several thousand spectators started to arrive we headed out for qualifying. Some crazy antics were the talk initially with several cars holding up the pack to create an area of empty track in front. It came to nothing other than a great photo opportunity (below) and in end there was plenty of room for 26 cars on track in the 20 minute session.
| Photo Chris Valentine - 88Racing.com |
Race 1
Unfortunately my fuel gauge had stuck on zero leading up to the race I somehow convinced myself I was marginal on fuel. I then messed up my start, reacting to the red lights coming on instead of going off, and having to jump on the brakes to avoid a jump-start. The lights then went out immediately and I was left stranded with no revs. I lost five places, including to slower Class-B cars.
Once I had gathered by thoughts and set about passing them back the main pack of Boxsters were 10 seconds up the track. My fuel garage came back to life and I had plenty so needn't have worried.
In my mirrors I had a fast approaching race spec Boxster which started from the pit lane. With 5 laps remaining he was on me and we swapped places four times in the space of two laps, until sadly for me, on the last lap I over cooked it into paddock hill, sliding wide gifting the place.
Race 2
I got a much better start, but didn't gain any places. Three laps of safety car, then ensued to clear two Class-B Boxsters who tangled right behind me on the first lap and ended up in the gravel.
Once racing resumed, the three cars in front (8th to 10th places) were battling and holding each other up, but I wasn't able to overtake. I also didn't want to get involved with what looked like some robust defending of position. One car eventually overshot into the gravel at Druids and I was closing in fast on 9th place as the chequered flag came out.
On retuning to the paddock my family and friends told me I was classified in 20th place and the commentators were announcing me as last and a lap down! After a long walk back to race control and a discussion with the tsl-timing reps they agreed my transponder had missed a lap at the end of the safety car period and they hadn't noticed.
Once the laps were corrected and the car in front disqualified for some over zealous defending of position, the race result was re-issued with me 9th.
Not the results that I wanted over the weekend, my target was 7th position. ( I actually get points for 7th due to guest drivers finishing in grant of me.)
It was the first time we have setup the car to have much more over-steer as opposed to my usual safer under-steer style. I managed to avoid any damage or spins and improved my best lap by over 1 second from last year.
Plenty of positives and only a few weeks until the final triple race meeting at Donington Park.
Labels:
Porsche festival,
race report
Friday, 18 July 2014
Rockingham Race Event
Arriving early Saturday morning we setup in the vast outer paddock. We had high hopes for the weekend, as its the first track of 2014 that I know. I qualified very well here last year despite not having success in the races.
Qualifying: I waited in the pits until last to find some empty track. It's debatable whether best to follow other cars, and maybe be held up or go it alone. I chose the latter.
After a lap to warm the tyres I found that the PSM stability control system wouldn't switch off! This this seemed to be severely limiting power out of the corners and felt like it was holding me back. I was 4 seconds off my expected pace, so pitted to see if we could quickly solve the problem. However everything we tried disabled ABS too - which would make things worse.
After a lap to warm the tyres I found that the PSM stability control system wouldn't switch off! This this seemed to be severely limiting power out of the corners and felt like it was holding me back. I was 4 seconds off my expected pace, so pitted to see if we could quickly solve the problem. However everything we tried disabled ABS too - which would make things worse.
I went back out for the last 5 minutes of the session and improved my lap time by over a second, but still 3 seconds slower than last year.
| Photograph http://www.dwmotorsportphotography.com/ |
Back in the paddock the guys from TF Motorsport and Jasmine showed us how to simply disable the PSM without affecting the ABS and we were confident of improving in the race.
Race 1: The temperature was in the high 20's as the lights went out. I got a reasonable start, holding position through the first corner. Half way round the lap, the two cars in front were side by and I nipped up the inside of one into the next. hairpin. As we got to the fast left hander Gracelands the two cars in front of me went in too fast, too wide, onto the marbles and started to spin. One went into the gravel but the closest rotated back across he track directly into my path. I had lifted off immediately I saw the spin which bought me a second to react and dodge right.
The old adage is that you aim for the spinning car, and it won't be there when you get there!
Unfortunately the cars behind me went left. I heard the collision, all three cars were out of the race with significant damage and the race red flagged.
On the restart I maintained position, but was always a second or two behind the cars in front. The heat was extreme and the harder I pushed the more mistakes I made, so came home 7th.
Race 2: Due to the general lack of grip and the twisty infield section we softened the rear roll-bar and the suspension for Sunday to find more grip and reduce the likelihood of under steer.
This turned out to be a good move when it started to rain just before the race. I try to treat light rain as nothing and race it as dry - but in the holding area it got worse, so I hastily got out and softened the suspension a little more.
With two warm-up laps permitted to get used to conditions I sought different lines through the corners searching for grip. It was very very slippery.
Off the line I got another great wet start, taking two places and holding on, despite a few moments over the first lap or two. A spinner in front put me 4th, a way back from the top 3 through. The next lap I started to consolidate my highest position ever and build a gap over 5th place. It all looked very promising!
Then the heavens opened, and a huge downpour ensued. Coming into the banked turn 1, I very nearly hit the wall; aquaplaning at 90mph, before recovering. My worn tyres unable to clear the depth of standing water.
Race control deployed the safety car (A Kia Rio) immediately. There was so much water I couldn't even keep up with it. My lap times had gone from 2:10 to 3:40 it was so bad. Once it pulled in 2 laps later I still couldn't get up to speed and was picked off one by one by the cars behind. I finally finished 9th on track and 7th in class.
Labels:
race report
Subscribe to:
Posts (Atom)






