With our first race of 2014 less than than a week away the car needed some final checks, a good clean and the championship decals to be fitted.
The final setup included setting and checking the ride height using the adjustable spring perches on the GAZ Gold dampers and choosing our initial damper and roll-bar settings for the Silverstone International circuit. Half a tank of fuel was also added so we can go straight out on track during testing.
We encountered a slight hitch initially when the car wouldn't start - despite a fully charged battery. We traced this to a poor earth connection from the battery to the car chassis, and after cleaning the connection everything worked perfectly.
The mandatory in-car camera was checked. We are using a BlackVue 12vpowered model which records constantly whilst the ignition is on. Our LUKE safety harnesses
were adjusted, before the car was given a thorough clean inside and out.
The amount of dirt and dust which accumulates inside is amazing.
The BRSCC Porsche Championship which we run in has a number of sponsors for 2014 (Toyo Tires / Jasmine PorschaLink / Fuchs Titan Race Fluids),
whose logos must be displayed in the correct places. In addition we
need the race numbers on each door, windscreen and dashboard, plus the safety stickers for the towing loops, electrical cut-off and fire extinguisher.
Monday, 31 March 2014
Monday, 24 March 2014
Final Preparations for 2014
Finishing the Winter overhaul took a bit longer than planned.
On replacing the leaking coolant hose, we found another leak, this time in a different hose. After this was replaced we were still dripping coolant, and this time we traced it to the water pump.
This is a time consuming job, since the front seat has to come out to get access through to the engine compartment. The pump was replaced with an uprated OEM part as well as the thermostat (which you have to remove to get access) and new gaskets. The thermostat is a low temperature version which is one way of limiting bore scoring in these Porsche engines.
In all we have refilled the coolant 3 times now - and hopefully that is the last time for a while. We are far too familiar with the process of bleeding the system, which takes around 45mins each time!
Our front brakes were worn
down to 2-3mm, so these have been changed along with new brake discs.
The pads are Mintex race pads, but the discs are OEM standard fit
drilled and vented ones for a 3.2S Boxster.
A new sports exhaust has also been purchased and fitted, saving around 10KG's of weight. This is significant, given the minimum weight limit is reduced this year by 20KG's.
The
final servicing work was to replace the engine oil and filter. We have
used the last of our Mobil 1 15-50 Motorsport oil. This oil is no
longer being produced so an alternative is needed for next time. Whilst
the oil was out we also changed a leaking seal on one of the camshaft
chain tensioners.
The replacement front bumper has been resprayed and fitted, giving the front end of the car a nice shiny look, ready for the updated 2014 championship decals to be fitted.
Labels:
brakes,
coolant,
exhaust,
servicing,
weight saving
Saturday, 14 December 2013
Start of the Winter Overhaul
Constantly alternating between full throttle, hard braking and high g-force cornering will take its toll on any car. The Porsche Boxster handles this better than most, so our winter overhaul is more akin to a full service and some preventative maintenance. No full strip down and rebuild needed!
First job was to remove the starter motor. This has been getting more and more sluggish recently, struggling to start the car when the engine is hot.
It
sits on top of the engine so removal of the throttle body and air
intake make it easier to get to. These are cleaned up as we go, as is
the BMC performance air filter which is has to be washed and re-oiled. A two- foot-long 2 foot socket extension is needed to get to the last bolt, which is accessed through the engine cover behind the seat.
| Top of the engine minus throttle body and starter motor |
While we are in this area of the engine, the oil air separator is notorious for failing, allowing oil to be sucked into the engine. Our intake showed some signs of oil residue. There is a motorsport version - but this isn't available for our earlier model car. Special hose clips and small arms from above and below are needed to replace this.
Lastly we turned our attention to underneath the car where we've been seeping fluid. A length of hose had to be cut out. Initially we thought this was power steering fluid, however it turned out to be coolant. Porsche factory fill with a yellow liquid which isn't available any more. Given the potential problems with mixing different coolant types we'll flush the system completely and refill after replacing the hose.
Phase two in the new year will be to change the oil and filter, then replace the front bumper. Finally we'll be removing more unnecessary wiring and getting a lighter weight exhaust fitted.
Monday, 21 October 2013
BRSCC Finals at Donnington Park
We arrived at Donington Park late Friday evening and unloaded into a Pit Garage. We'd hired a different trailer this weekend and found out too late that you cannot open the car doors due to the high wheel arches. This meant climbing in though the roof to get the car off the trailer which was entertaining.
Qualifying (Saturday 11am)
The track was wet from overnight rain and the single seaters before us were out on full wet tyres kicking up spray down the main straight. I expected it to dry out, and my lap times increased throughout the session as a dry line appeared in places. Everyone went fastest on the last lap, but I was hampered a little by traffic so could have gone quicker. I qualified 12th.
| Photo Courtesy of @Sportscarfan917 |
Race 1 (Saturday 4pm)
I got a decent start off the line but several cars jumped the start, rolling before the lights went out. As I rounded the first corner (Redgate) the cars in front suddenly all swerved left (to avoid a spinning car). I had to take avoiding action, ending up with two wheels in the gravel and two in the mud verge going nowhere fast. By the time I rejoined the circuit I was almost dead last.
The 20 min race saw me pass all of the 924 runners, the two production boxsters and catch the race spec boxsters. There were no blue flags to help as we were racing for position. I crossed the line side by side with 13th place (0.2 secs behind). Both of us gained an extra place when the jump start penalties (10 secs) were applied.
I got a decent start off the line but several cars jumped the start, rolling before the lights went out. As I rounded the first corner (Redgate) the cars in front suddenly all swerved left (to avoid a spinning car). I had to take avoiding action, ending up with two wheels in the gravel and two in the mud verge going nowhere fast. By the time I rejoined the circuit I was almost dead last.
The 20 min race saw me pass all of the 924 runners, the two production boxsters and catch the race spec boxsters. There were no blue flags to help as we were racing for position. I crossed the line side by side with 13th place (0.2 secs behind). Both of us gained an extra place when the jump start penalties (10 secs) were applied.
After the race we noticed the exhaust was sounding pretty rough. On stripping the bumper off we found the lambda probe had corroded and blown out of the catalytic converter leaving a 50p piece size hole. With the help of Tony from Southshore Tyres we managed to weld it back on, racing with a blowing exhaust.
Race 2 (Sunday 12pm)
Having rained in the morning the track was still wet for our 12pm race. I knew it would dry quickly so set dampers fairly stiff, mindful it would be slippy off-line.
The race was red flagged at 2/3 distance and restarted for an accident. I finished my best ever in 6th having great battles with other cars for that position in both parts. The car handled really well and my driving was quite smooth - although my lap times were 1 second slower than 2012.
Race 2 - Part 1 Video / Race 2 - Part 2 Video
Race 3 (Sunday 4pm)
With confidence high we stiffened roll bars and dampers for the last race which was a reverse grid (starting 8th in boxsters). Just before we went out a torrential downpour soaked the track so we hastily changed to a wet setup. Race 3 (Sunday 4pm)
On lap 1 visibility was almost zero from spray and I got stuck behind a train of cars whilst faster cars overtook all of us. On lap two I used the wet race line with good effect to take 3 places back and open a big gap. I was now in 6th place. A car spun on the oil immediately in front of me resulting in a very close call.
I eventually got caught on the last lap - finishing a very happy 6th place again!
Labels:
exhaust,
race report
Monday, 14 October 2013
Donnington Park Wet Practice
With no Friday test being offered by Donnington Park we chose a Bookatrack trackday the week before our race weekend to get some practice laps in.
At a first glance Bookatrack look a little more expensive that some other track day operators. However their approach is to limit the no. of cars taking part (up to half of other track days) which ensures you get maximum track time from the day.
The day was well really run, with a mix of race,track and supercars all behaving on track in pretty tricky wet conditions. Persistent rain for most of the day threatened to close the track at times as rivers of water flowed across the tarmac in several places.
We used the day to asses wet weather handling at different tyre pressures and damper settings. We also experimented with different race lines. Overall we improved our times by 4-5 seconds by the end of the day in worsening conditions.
We also tested out a new hardwired Blackvue camera to meet a newly introduced championship regulation (mandatory in car camera recording). This records whenever the ignition is on saving us the aggravation of usb charging, memory card management and forgetting to press the record button!
Saturday, 7 September 2013
Steering Arm Replacement
We noticed quite a while ago (last year in fact) that one of our steering arms was badly bent at the join with the track rod end. Since we are skipping a couple of race events, after a busy summer, this job has now reached the top of the priority list.
Having put the car on axle stands, removed the wheel and front under-tray, you can get access to the inner joint of the steering arm.
There is a design fault though! The steering column wont extend far enough to clear the front sub-frame and enable you to get a spanner onto the inner joint. As it happens we had the perfect offset 32mm wrench already in our toolbox. It's a special offset wrench for tightening a Ford / BMW engine fan from the 1990's.
With the inner joint undone it took another half an hour to reassemble, ensuring the same no. of threads were showing at the adjustment end so the tracking would not be wildly out.
Once finished we reset the tracking using our basic strings approach, setting 2mm of tow out in place of our previous straight alignment. In theory this will help the car turn in on the corners. This is quite aggressive and we'll see if it makes a difference when we practice for the Donnington Park round in October.
Having put the car on axle stands, removed the wheel and front under-tray, you can get access to the inner joint of the steering arm.
With the inner joint undone it took another half an hour to reassemble, ensuring the same no. of threads were showing at the adjustment end so the tracking would not be wildly out.
Once finished we reset the tracking using our basic strings approach, setting 2mm of tow out in place of our previous straight alignment. In theory this will help the car turn in on the corners. This is quite aggressive and we'll see if it makes a difference when we practice for the Donnington Park round in October.
Subscribe to:
Posts (Atom)


