Monday, 30 April 2012

Final Preparations

The weekend before the Snetterton race we still had a number of jobs to complete.

Adjusting the rear tow straighter as I didn't like the feel of the car at the last track day and the race would all be about confidence to push the car.

The aluminium bottle fire extinguisher kit which is from a UK company called FEV was mounted in the car in place of the passenger seat we had during track days.  The supplied tubing was cut and run to four spray nozzles (2 in the driver compartment and 2 in the engine bay) and connected up with t-pieces.
It is fired by externally and internally mounted self powered buttons with a control box to test and arm the system. The E Is for Extinguisher not Electrics!
 
The final job was to re-fit the standard air box with a performance filter to ensure we were compliant with the series regulations, removing the induction system previously fitted.

Sunday, 1 April 2012

Snetterton Shakedown 2

On 30th March we were at Snetterton in Norfolk again.  After passing my ARDS test in the morning (see previous post) we had more running on track. Mechanically the car ran well and reliably.
The day was an open pit lane event and there were really too many cars at the event. Track time was disrupted continuously by red flag incidents and lots of traffic.  Later in the afternoon we ran our race wheels and Toyo 888 tyres - however suffered some rubbing on the rear arches in hard cornering which will need more rolling and trimming of the inner wheel arches to fix.

LetsGoRacing!

I have signed up to be a driver in the 2012 Logson Group Porsche Championship run by the British Racing & Sports Car Club (BRSCC). This championship has classes for Porsche Boxster and Porsche 924 race cars on a mixed grid.

 

One of the final hurdles before entering the championship was to pass my Association of Racing Driver Schools (ARDS) test.  This provides me with a Motorsports Association National 'B' race licence. This is a two-part test comprising a written test of the flags and safety procedures plus a 2-lap driving test.  I passed with 100% in the written test and with a mix of good and average marks in the driving test. I drive the Peugeot RCZ for the driving test and found just couldn't get used to the clutch and brake pedal. Very different from the the Boxster - still I managed to get round safely to pass!
Our car will run no. 46 in the championship with our first race being the 2nd Round at Snetterton on the 28th April 2012.
 
 There is still lots to do to get the car within the regulations and ready to race!

Race Wheels and Tyres


Work on the car continues.  Some of the car under tray was flapping loose so needed to be repaired.  The heat shielding on the underside of the rear boot floor (above the exhaust) also rattles - but this will wait until the exhaust box is changed as access is difficult.

After the last track day we needed to replace the brake fluid with Castrol SRF and adjust the rear tow slightly.  Our method of running parallel fishing wire lines down each side of the car is basic and cheap - but effective. 
 
We then trial fitted our Team Dynamics Race Wheels.  These need at least a 3mm spacer at the rear to avoid the rim hitting the suspension tower. They have the medium compound Toyo 888 tyres fitted and should make a massive difference in handling on track.

Saturday, 24 March 2012

Front Tow Stap and Timing Transponder

More work has been completed on the front of the car this time.  The bumper was removed and the front air conditioning condensors were taken out to reduce a bit of weight.  These were fitted directly in-front of the water radiators which can be seen in the photo below.
The front tow strap was fitted in the same manner as the rear and the timing transponder (the small red box) was also fitted.  This is a mandatory item for racing and is positioned 30-60cm's off the road facing down towards the track.  Each unit has a unique serial no. which will enable the circuit timing systems to pickup our car as it travels over the timing strip buried into the track surface on the start/finish line.
The bumper also had some paint and a clear coat applied to cover some previous damage and was re-fitted.

Tuesday, 6 March 2012

Tow Straps

A requirement for racing is front and rear towing hooks, eyes or straps.  I don't like the metal ones as they can cause a lot of damage to to other cars in accidents (as we've found out ourselves) so we are fitting fabric tow straps.

The rear bumper was removed and the strap fitted to the top of the bumber bar.
A slot was then cut in the bumper to feed the strap through and folded up with an elastic band when we're not on the track.
Tow stickers will beput on the bumper adjacent to the the straps to ensure marshals can easily find the towing points on the car.