The rollcage took longer than expected to be delivered, but is now fully fitted and ready to be painted before we re-assemble the race interior.
The wiring loom on the left and right hand sides (including the relay board and fusebox) have to be re-attached. The heater unit from under the passenger side dashboard also needs to to be re-installed with appropriate modification to fit around the rollcage bars.
Sunday, 20 November 2011
Sunday, 16 October 2011
Roll Cage
All of the remaining interior trim and dashboard elements have been removed to allow the installation of the rollcage.
The dashboard took a morning to remove and was quite straightforward. How easily it goes back in remains to be seen!
Off we go on our first towing experience!
The dashboard took a morning to remove and was quite straightforward. How easily it goes back in remains to be seen!
The car was winched onto a trailer we hired for the day. We took it to Roll Centre who are fitting the cage for us. The car is so low that extra ramps were needed to reduce the angle onto the trailer and stop the car grounding.
The car had to be put onto the trailer backwards in the end so the weight distrubution was correct. The trailer bed should be flat under its own weight and the hitch end still be able to be lifted easily.Off we go on our first towing experience!
Labels:
modifications,
rollcage,
trailer
Rear Suspension (Part 2)
The used hub assemblies ordered turned out to be in worse condition that our existing ones with both damaged threads and worn wheel bearings. As an alternative we sent the hubs away to be drilled out and time steel inserts http://www.timesert.com/ put in. This is apparently a common problem on caliper, head and spark plug bolts.
Both sides of the rear suspension were re-assembled in a day and the alignment adjusted by eye initially with maximum negative camber and zero toe in/out.
The new discs and race pads installed as per the front. The ride height is adjusted on the spring perches and was set to give us ~10mm above the minimum series ride height (85mm).
Both sides of the rear suspension were re-assembled in a day and the alignment adjusted by eye initially with maximum negative camber and zero toe in/out.
The new discs and race pads installed as per the front. The ride height is adjusted on the spring perches and was set to give us ~10mm above the minimum series ride height (85mm).
We can go lower if we needed but may have to roll the inner wheel arches.
Labels:
brakes,
modifications,
suspension
Sunday, 18 September 2011
Rear Suspension (Part 1)
We started the rear suspension change in the knowledge it would be a substantial job and more complex than the front suspension.
With the car on stands and the wheels off, we set about removing the brakes. The pads came out easily using the rusty pin technique learned on the front suspension change. The first problem came immediately after - removing the brake caliper bolts. On investigation the ends of the bolts protrude through the wheel hub assembly and had corroded badly. This corrosion damanged the threads on the hub assembly.
With two used replacement wheel hub assembly's ordered, the revised task list now included loosening the main hub nut to pull the hub off the drive shafts. This required 5mins of heating from a blow torch, a 32mm deep socket, 1.5ft breaker bar with 2ft extension pole and the force of two adults. It was tightened to 460lbs/ft at the factory with added loctite!
Knowing the job would overrun we moved the car into the garage and spent the rest of the day removing the the suspension and wheel hub assembly.
A large assortment of different size sockets and spanners were needed, plus long ratchet extensions and torque wrenches. The hub assembly came off with use of a pulley puller after a balljoint separator disconnected the suspension arms. One side was completed fully by the end of the day and is ready for the new parts to be installed next week.
With the car on stands and the wheels off, we set about removing the brakes. The pads came out easily using the rusty pin technique learned on the front suspension change. The first problem came immediately after - removing the brake caliper bolts. On investigation the ends of the bolts protrude through the wheel hub assembly and had corroded badly. This corrosion damanged the threads on the hub assembly.
With two used replacement wheel hub assembly's ordered, the revised task list now included loosening the main hub nut to pull the hub off the drive shafts. This required 5mins of heating from a blow torch, a 32mm deep socket, 1.5ft breaker bar with 2ft extension pole and the force of two adults. It was tightened to 460lbs/ft at the factory with added loctite!
Knowing the job would overrun we moved the car into the garage and spent the rest of the day removing the the suspension and wheel hub assembly.
A large assortment of different size sockets and spanners were needed, plus long ratchet extensions and torque wrenches. The hub assembly came off with use of a pulley puller after a balljoint separator disconnected the suspension arms. One side was completed fully by the end of the day and is ready for the new parts to be installed next week.
Labels:
modifications,
suspension
Monday, 11 July 2011
Front Suspenson and Brakes Overhaul
Finally the Gaz Gold coil-over suspension has arrived. These are 2-way adjustable (height and dampening) and come as complete units with springs. Removing the old brake pads took several hours due to he pins being rusted in. The pads and discs have clearly have not been replaced for a long time.
The suspension units were fitted and adjusted to give the maximum negative camber possible, followed by replacement standard vented discs.
The standard 'Big Red' Bembo 4 Pot callipers were cleaned up. The the retaining bracket and pins had all the rust sanded off and were painted in aluminium rust proof paint. Mintex racing brake pads were fitted.
Labels:
modifications,
suspension
Monday, 20 June 2011
Dashboard Modifications
The steering lock mechanism has been removed to adhere to MSA regulations.
The lock mechanism required the steering wheel, instrumentation, ignition switch and heater vent to be removed to gain access, before we cut the locking pin off with a dremel tool and re-fitted. This looks quite a but more complex that it was and was good practice since the whole dashboard will need to come out when the roll-cage is fitted.
On the passenger side the airbag behind the dashboard panel was also removed and the panel fitted.
The Porsche PCM Radio & Sat Nav unit has also been removed and will be sold. The area is blanked with a carbon fibre sheet and will have the interior safety cut-off and fire switches mounted to it as well as re-instating a button for the horn. The lower fan control unit is being retained.
Labels:
modifications
Subscribe to:
Posts (Atom)


